Contact Us:
sales@inosaki.com
[fusion_table fusion_table_type=”1″ fusion_table_rows=”” fusion_table_columns=”” margin_top=”” margin_right=”” margin_bottom=”” margin_left=”” hide_on_mobile=”small-visibility,medium-visibility,large-visibility” class=”” id=”” animation_type=”” animation_direction=”left” animation_color=”” hue=”” saturation=”” lightness=”” alpha=”” animation_speed=”0.3″ animation_delay=”0″ animation_offset=””]
Control the output | Supply voltage | 11PIN type | 8PIN type |
---|---|---|---|
Output by Dot:
DPDT (Time-limited output) |
AC110V (50/60Hz) | H3BA-N AC110V | – |
AC220V (50/60Hz) | H3BA-N AC220V | ||
DC24V | H3BA-N DC24V | ||
Output by Dot:
Limited time SPDT with SPDT can be switched (Limited time ↔, instantaneous) |
AC110V (50/60Hz) | – | H3BA-N8H AC110V |
AC220V (50/60Hz) | H3BA-N8H AC220V | ||
DC24V | H3BA-N8H DC24V |
[/fusion_table]
[fusion_table fusion_table_type=”1″ fusion_table_rows=”” fusion_table_columns=”” margin_top=”” margin_right=”” margin_bottom=”” margin_left=”” hide_on_mobile=”small-visibility,medium-visibility,large-visibility” class=”” id=”” animation_type=”” animation_direction=”left” animation_color=”” hue=”” saturation=”” lightness=”” alpha=”” animation_speed=”0.3″ animation_delay=”0″ animation_offset=””]
project | H3BA-N | H3BA-N8H |
---|---|---|
Action mode | A: ON Delay B: Flashing OFF Start B2: Flashing ON Start C: Signal ON/OFF Delay D: Signal OFF Delay E: Interval G: Signal ON/OFF Delay J: Monostable output |
A: ON Delay H: ON Delay with Instantaneous Output Contact |
Pin type | 11pin | 8pin |
Input method | No voltage input | — |
Output mode | DPDT (Limited Time) | SPDT (time-limited) vs. switchable SPDT (time-limited<—>instant) |
Installation: | Aluminum rail mounting, surface mounting, and flush mounting | |
Applicable Standards | UL508, CSA C22.2 No.14, LR and CCC : GB/T 14048.5* according to EN 61812-1 (Pollution 2 / Overvoltage Category III) |
|
EMC | (EMI) EN 61812-1 Radiological hazard intensity: EN 55011 class A AC power supply immunity: EN 55011 class A (EMS) EN 61812-1 8kV Air Discharge 1V/m (2GHz~2.7GHz AM modulation) 10V/m (900MHz pulse modulation) Conducted Noise Immunity: EN 61000-4-6: 10V (0.15MHz~80MHz) Radio Pulse Immunity: EN 61000-4-4: 2kV power cord 2kV I/O Signal Line 1kV Different Modes |
[/fusion_table]
*About CCC acquisition conditions
[fusion_table fusion_table_type=”1″ fusion_table_rows=”” fusion_table_columns=”” margin_top=”” margin_right=”” margin_bottom=”” margin_left=”” hide_on_mobile=”small-visibility,medium-visibility,large-visibility” class=”” id=”” animation_type=”” animation_direction=”left” animation_color=”” hue=”” saturation=”” lightness=”” alpha=”” animation_speed=”0.3″ animation_delay=”0″ animation_offset=””]
Proposed fuses | 0216005 (250VAC, 5A) manufactured by Littelfuse |
---|---|
Rated operating voltage Ue Rated operating voltage Ie |
AC-15: Ue: 250VAC, Ie: 3A AC-13: Ue: 250VAC, Ie: 5A DC-13: Ue: 30VDC, Ie: 0.1A |
Rated insulation voltage | 250V |
Rated impulse voltage (Height: 2000m or less) |
4kV (at AC240V) |
Conditional short-circuit current | 1,000A |
[/fusion_table]
[fusion_table fusion_table_type=”1″ fusion_table_rows=”” fusion_table_columns=”” margin_top=”” margin_right=”” margin_bottom=”” margin_left=”” hide_on_mobile=”small-visibility,medium-visibility,large-visibility” class=”” id=”” animation_type=”” animation_direction=”left” animation_color=”” hue=”” saturation=”” lightness=”” alpha=”” animation_speed=”0.3″ animation_delay=”0″ animation_offset=””]
Units of time | s (seconds) | x 10s
(10 seconds) |
min
(min) |
x 10min
(ten minutes) |
h
(hours) |
x 10h
(10 hours) |
|
---|---|---|---|---|---|---|---|
Full scale setting | |||||||
1.2 | Set the time | 0.05~1.2 | 1.2~12 | 0.12~1.2 | 1.2~12 | 0.12~1.2 | 1.2~12 |
3 | 0.3~3 | 3~30 | 0.3~3 | 3~30 | 0.3~3 | 3~30 | |
12 | 1.2~12 | 12~120 | 1.2~12 | 12~120 | 1.2~12 | 12~120 | |
30 | 3~30 | 30~300 | 3~30 | 30~300 | 3~30 | 30~300 |
[/fusion_table]
[fusion_table fusion_table_type=”1″ fusion_table_rows=”” fusion_table_columns=”” margin_top=”” margin_right=”” margin_bottom=”” margin_left=”” hide_on_mobile=”small-visibility,medium-visibility,large-visibility” class=”” id=”” animation_type=”” animation_direction=”left” animation_color=”” hue=”” saturation=”” lightness=”” alpha=”” animation_speed=”0.3″ animation_delay=”0″ animation_offset=””]
project | H3BA-N | H3BA-N8H |
---|---|---|
Rated supply voltage
(Please refer to Notes 1 and 2) |
AC110V (50/60Hz)、AC220V (50/60Hz)、DC24V | |
Voltage range of use
(See Note 3) |
85%~110% of rated power supply voltage | |
Power restoration | Minimum power on time: 0.1s | |
No voltage input | Impedance at ON: 1 kΩ or less Residual voltage at ON: 1 V or less Impedance at OFF: 200 kΩ or more |
|
Power consumption | AC110V: Approx. 4.6VA (1.5W) AC220V: Approx. 7.6VA (1.3W)
DC24V: Approx. 0.6W |
AC110V: Approx. 3.6VA (1.6W) AC220V: Approx. 7.8VA (1.9W)
DC24V: Approx. 0.9W |
Control the output | Contact: 5A at 250V AC, resistive load (cosφ = 1) |
[/fusion_table]
Note 1. The DC ripple rate is less than 20%.
Note 2. Using models other than the DC24V H3BA-N type will generate a surge current.
When powering on these models through a contactless output such as a sensor, be aware of the surge current.
Note 3. If the timer is used continuously at high ambient temperatures, the DC standard ripple rate is 90% or higher.
[fusion_table fusion_table_type=”1″ fusion_table_rows=”” fusion_table_columns=”” margin_top=”” margin_right=”” margin_bottom=”” margin_left=”” hide_on_mobile=”small-visibility,medium-visibility,large-visibility” class=”” id=”” animation_type=”” animation_direction=”left” animation_color=”” hue=”” saturation=”” lightness=”” alpha=”” animation_speed=”0.3″ animation_delay=”0″ animation_offset=””]
project | H3BA-N | H3BA-N8H |
---|---|---|
Accuracy of action time | ± 0.3% FS or less (±0.3% ±10ms in 1.2s range) | |
Setting error | ±5% FS ±0.05s or less | |
Return time | Minimum power on time: 0.1s or less Minimum pulse input time: 50ms |
|
Voltage effects | ± 0.5% FS or less (±0.5% ±10ms in 1.2s range) | |
Temperature effects | ±2% FS or less (±2% ±10ms in the 1.2s range) | |
Insulation resistance | 100MΩ min. (at 500 VDC) | |
Withstand voltage | AC2,000V, 50/60Hz 1min (between conductive metal and exposed non-conductive metal) AC2,000V, 50/60Hz 1min (between control output terminal and operation circuit) AC1,000V, 50/60Hz 1min (between non-continuous contacts) (AC750V for H3BA-N8H type) | |
Impulse voltage | 1kV (between power terminals) 2kV (between conductive terminals and exposed non-conductive metal parts, 1.5kV for DC24V type) | |
Noise resistant | Type AC:
± 1.5kV (between power terminals) and 600V (between input terminals) ± Square wave noise generated by noise simulator (pulse width: 100ns/1μs, 1ns rise) ± 480V (between power terminals), ± 600V (between input terminals). Square wave noise generated by the noise simulator (pulse width: 100ns/1μs, 1ns ramp) |
|
Resistant to static electricity | Malfunction: 4kV Durability: 8kV | |
Vibration resistant | Durability: 10~55Hz, 0.75mm single amplitude, 3 directions, 1 time each Malfunction: 10~55Hz, 0.5mm single amplitude, 3 directions, 1 time each |
|
Impact-resistant | Durability: 1,000 m/s2 (approx. 100 G), 3 directions, 1 time each Malfunction: 100 m/s2 (approx. 10 G), 3 directions, 1 time each |
|
Ambient temperature | Operation: -10°C~55°C (no icing) Storage: -25°C~65°C (no freezing) | |
Ambient humidity | Operation: 35%~85% | |
Service life | Mechanical: 10,000,000 cycles or more (1,800 cycles/hour at no load) Electrical: 100,000 cycles or more (AC250V 5A Resistive Load, 1800 times/hour) |
Mechanical: 10,000,000 cycles or more (1,800 cycles/hour at no load) Electrical: 100,000 cycles or more (AC250V 5A Resistive Load, 360 times/hour) |
Housing color | Light grey (Munsell 5Y7/1) | |
Ingress protection | IEC: IP40 (panel surface) | |
weight | Approximately 95g |
[/fusion_table]
Note. To set the timer limit to a loop of less than 3 seconds or to use forced reset, use the H3BA-N type D mode (signal OFF delay).
Model | H3BA-N AC110V, H3BA-N AC220V, H3BA-N DC24V, H3BA-N8H AC110V, H3BA-N8H AC220V, H3BA-N8H DC24V |
---|
INOSAKI Limited
RM B 5/F Gaylord Comm,
Bldg 114-118 Lockhart Rd.
Hong Kong
INOSAKI Sdn. Bhd.
2-1-9, Ground Floor, One Square, Tingkat Mahsuri 1,
11900 Bayan Lepas, Penan
INOSAKI Pte. Ltd.
101 Upper Cross Street,
No. 06-17, People’s Park Centre,
Singapore (058357)
inosaki.com 2008 -2024